Parts index


We stock over 22 Engine tools

We stock a wide range of tools for working on your Lambretta engine. From our engineering background we firmly believe in using the right tool for the job, so we made our own tools. The tools are either based on original items or are from our own design.


Showing parts 1 - 22 of 22

20   |  40   |  ALL   |

Sort by:


Lambretta Tool, allen key, 3.5mm, Italian gear trunnions
MBL0007

This is the unusually sized allen key you need for most gear and clutch cable trunnion on a Lambretta.... [more]


£ 1.94£ 1.62 (Ex Vat)
Lambretta Tool, rear hub puller (extractor) S 1, 2, 3, MB
MBP0358K

Using this tool is the best and safest way to remove your Series 1, 2 and 3 Lambretta rear hubs.    You simply bolt... [more]


£ 36.35£ 30.29 (Ex Vat)
£ 0.71£ 0.59 (Ex Vat)
£ 0.71£ 0.59 (Ex Vat)
Lambretta Tool, alley key, 10mm, crankcase side drain plug
MBL0703

This allen key can be used for the crankcase side drain and level plugs amongst other things.... [more]


£ 1.61£ 1.34 (Ex Vat)
Lambretta Tool, dial gauge only, 10mm travel, MB
MBL1390

This is a high quality 10mm movement dial gauge.    It can be used with our cylinder head dial gauge bracket kit to set... [more]


£ 16.80£ 14.00 (Ex Vat)
Lambretta Tool, clutch holder, MB
MRB0149

This is a MB steel clutch holder, which will let you safely and easily hold your clutch assembly while you undo and tighten the... [more]


£ 21.60£ 18.00 (Ex Vat)
Lambretta Tool, clutch compressor, MB
MRB0150K

This is our MB Lambretta clutch compressing tool.    Designed to safely compress your clutch while you change the clutch plates.    It mounts... [more]


£ 35.04£ 29.20 (Ex Vat)
Lambretta Tool, T bar extractors, magneto housing and end plate, pair, MB
MRB0155

Another tool copied from the original with a slight MB improvement.    We remade these T bar extractors in slightly different lengths so the handles ... [more]


£ 14.36£ 11.97 (Ex Vat)
Lambretta Tool, con rod holding, MB
MRB0156

This tool will work on any single cylinder vehicle.    It is designed to rest on the base gasket face and hold your con-rod (and therefore... [more]


£ 24.04£ 20.03 (Ex Vat)
Lambretta Tool, spare wheel jack stand, MB
MRB0157

This is a copy of the original tool as supplied with all new Lambrettas.    It fits in a small hole under the rear of your... [more]


£ 5.26£ 4.38 (Ex Vat)
Lambretta Tool, crankshaft drive side pulling sleeve, MB
MRB0201

There is no point spending money on a crank that has been checked for alignment then going and hitting it with a hammer to... [more]


£ 17.20£ 14.33 (Ex Vat)
Lambretta Tool, drift large magneto seal, MB
MRB0202

Fitting the large oil seal into the magneto flange can be quite difficult so Mark came up with this tool to easily and squarely... [more]


£ 11.04£ 9.20 (Ex Vat)
Lambretta Tool, drift end plate bearing, MB
MRB0251

This MB tool is designed to make it easy and safe to refit the gearbox end plate bearing with out damaging the bearing.    It's designed... [more]


£ 17.30£ 14.42 (Ex Vat)
Lambretta Tool, final drive (puller) pulling sleeve, MB
MRB0252K

It is important when fitting the layshaft and checking the tolerances in the gearbox, that the layshaft is pulled all the way into the... [more]


£ 12.91£ 10.76 (Ex Vat)
Lambretta Tool, flywheel holder (holding) double ended, MB
MRB0253

This tool will hold 90% of Lambretta flywheels.    It is double ended and will hold normal Italian Series 3 type flywheels as well as the... [more]


£ 23.05£ 19.21 (Ex Vat)
Lambretta Tool, drift flywheel side inner sleeve, MB
MRB0254

This tool is designed to safely and easily fit the inner bearing sleeve from a flywheel bearing to the crank.    You just fit the sleeve... [more]


£ 19.75£ 16.46 (Ex Vat)
Lambretta Tool, cylinder head dial gauge bracket kit (no dial gauge) MB
MRB0415K

This bracket kit is designed to be used with any Lambretta, P range, T5 or small frame Vespa.   It is designed to put your... [more]


£ 20.33£ 16.94 (Ex Vat)
Lambretta Tool, cylinder head dial gauge and bracket kit, MB
MRB0433K

This Dial gauge bracket kit is designed to be used with any Lambretta, Vespa P range, T5 or small frame Vespa.    It is... [more]


£ 37.13£ 30.94 (Ex Vat)
Lambretta Tool, timing disc, metal, MB
MRB0662

This timing disc has been specially designed by us for using on Lambrettas and can be used on engines fitted with GP crankshafts.   ... [more]


£ 19.33£ 16.11 (Ex Vat)
Lambretta Tool, allen key, 4mm, T Handle for drive side screws
MBU0270

This simple allen key tool is ideal for the drive side sealing plate screws.  It is also used on my other universal fasteners.... [more]


£ 4.25£ 3.54 (Ex Vat)
Lambretta Tool, Drive side bearing fitting and removing, MB
MRB0966

Theres plenty of ways to fit and remove a bearing, it's the same with a drive bearing. On a good casing if warmed enough a... [more]


£ 34.32£ 28.60 (Ex Vat)