Parts index
We stock over 25 Main engine & side casing spares
This section contains all the main engine & side casing spares we offer.
MBB0033
A high quality gear cluster needle bearing. This sits in your engine casings underneath the gear cluster.... [more]
MBFEC10SC
Amongst many applications this fastener can specifically be used on the GP clutch arm, inside the casing.... [more]
MBFPWA16
MB made stainless steel engine bar washer, can also be used on the rear shocker. Amongst many applications this fastener can specifically be used under... [more]
MBL0132
These standard 7mm dowels fit in your engine case and are used to locate the crankcase side and the gearbox end plate. Two per end plate. Two... [more]
MBL0134
This fibre washer sits between the level, drain and filler plugs to provide a seal. You need 3 per crankcase side.... [more]
MBL0154
Fed up with inferior supplies where we couldn't guarantee size tolerances we made our own. This track/bush is pressed into the gearbox endplate and the... [more]
MBL0155
This rubber item sits in a hole on the top of your casing and supports your frame on your engine when the rear shocker... [more]
MBL0161PR
This pair of MB stainless steel engine cones that sit in the two holes on your frame and the engine bar goes through the... [more]
MBL0218
This bush sits in your casing and the gear cluster and bearing runs in it. They rarely wear because they should run in oil... [more]
MBL0223
MB made gear selector arm bush for all models. This bush sits in your casing and the gear arm goes through it. It does... [more]
MBL0404
This small rubber fits into the crankcase side to stop the kick-start pedal when it springs back up. Specially made for MB, now with a... [more]
MBL1082
This is a remade engine bar to suit any Series 1, 2 or 3 Lambretta with the small type engine mounts.... [more]
MBL1365
This is a base gasket for all 125/150/175cc casings. It is approximately 1mm thick so can be added or left out to get your squish... [more]
MBP0181
This is a top quality reuseable - standard thickness 0.8mm crankcase side gasket. Fit all Series 1, 2 or 3 crankcase sides (except TV Series... [more]
MRB0205
Another excellent idea from MB made specially to work in conjunction with our longer high tensile cylinder studs. They are just over three... [more]
MRB0239K
This two part head is cast for us in heat treated aluminium and then we machine it to suit your cylinder. It can... [more]
MRB0240K
This is our special heat treated aluminum cast performance center plug cylinder head. It is designed to fit under a normal Lambretta... [more]
MRB0241K
This is our original special heat treated aluminum cast oversized center plug head. The biggest and best cooling head on the market. It... [more]
MRB0242
We have had these nuts remade and zinc plated. It is the one that fixes your cylinder head on then the bolt that... [more]
MBP0064
We were disappointed with the quality of the level plugs available so we made them in stainless steel. Idea on their own or in our... [more]
MBP0069
We were disappointed with the quality of all the drain plugs available, so we made our own in stainless steel. It is fitted with a... [more]
MBP0082K
Our new MB Road - Race filler breather cap. Made from stainless steel, designed by Mark Broadhust. Comes with a length of... [more]
MBP0103
When stripping a scooter down it is common to find that the engine bar is rusted in and can sometimes be a nightmare to... [more]
MBP0104
When stripping a scooter down it is common to find that the engine bar is rusted in and it can sometimes be a nightmare... [more]
MBP0136
This MB plate sits on top of the two brake shoe pivots and is held in place by two circlips. Li Sx Tv only... [more]