Lambretta Race-Tour Inlet manifold, TS1, flange type, manifold only, MB

MRB0869K

New style inlet manifold from MB Scooters.

Uses a flange type rubber to increase panel clearance and facilitate the use of different types of carburettors.

The manifold has a slight recess on the reed block surface for improved frame clearance.

Kit comprises;

  • Inlet manifold
  • Inlet gasket
  • All fasteners

Advantages are;

  • Lifts the carb giving greater panel clearance and aids fitting a air filter
  • Lifting the carb gives greater cable clearance on gears/clutch/rear brake
  • Lifting the carb means better fuel pipe clearance
  • Easier to get to air and idle screws

TOP TIP: Use gasket sealer of faces and under the 6mm allen bolt head to prevent air leaks

TIP - Silicone seal the rubber and gaskets in place

WARNING - these fit perfect with standard tanks, they may not fit with aftermarket tanks



Lambretta Race-Tour Inlet manifold, TS1, flange type, manifold only, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, manifold only, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, manifold only, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, manifold only, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, manifold only, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, manifold only, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, manifold only, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, manifold only, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, manifold only, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, manifold only, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, manifold only, MB

£ 24.50
Price: £ 20.42 Ex Vat



Related Items (6)

Lambretta Race-Tour Inlet manifold, TS1, flange type, Dellorto PHBL, MB
MRB0870K

New style inlet manifold from MB Scooters. Uses a flange type rubber to increase panel clearance and facilitate the use of different types of carburettors. The... [more]


£ 41.96£ 34.97 (Ex Vat)
Lambretta Race-Tour Inlet manifold, TS1, flange type, Dellorto PHBH, MB
MRB0871K

New style inlet manifold from MB Scooters. Uses a flange type rubber to increase panel clearance and facilitate the use of different types of carburettors. The... [more]


£ 42.59£ 35.49 (Ex Vat)
Lambretta Race-Tour Inlet manifold, TS1, flange type, Mikuni 35mm TMX, Amal 28-34mm, MB
MRB0872K

New style inlet manifold from MB Scooters. Uses a MB flange type rubber to increase panel clearance and facilitate the use of different types of... [more]


£ 48.52£ 40.43 (Ex Vat)
Lambretta Race-Tour Inlet manifold carb mounting rubber flange type, Dellorto PHBH, Viton, MB
MRB0833

This is a Mark Broadhurst redesigned, improved and strengthened flange type carb mounting rubber.     Suits: Dellorto PHBH carbs 26, 28, 30mm Dellorto VHSH 30mm Dellorto... [more]


£ 16.20£ 13.50 (Ex Vat)
Lambretta Race-Tour Inlet manifold carb mounting rubber flange type, Mikuni TMX 35mm, Amal 28-35mm, MB
MRB0819

This is a Mark Broadhurst redesigned, improved and strengthened flange type carb mounting rubber.     Suits all Mikuni 32 - 35mm and Amal... [more]


£ 19.14£ 15.95 (Ex Vat)
Lambretta Race-Tour Inlet manifold carb mounting rubber flange type, Dellorto PHBL, MB
MRB0817

This is a Mark Broadhurst redesigned, improved and strengthened flange type carb mounting rubber.     Suits all Dellorto 22 - 26mm PHBL and... [more]


£ 15.58£ 12.98 (Ex Vat)


Tips

  • The manifold is made with a round hole to suit directly into V Force reed bloocks which give the best power
  • We have reed stuffers for Genuine Yamaha and Bgm reed assemblys so they fit perfect into the round hole
  • If using a square hole reed assembly they can easily be modified to suit but should flow quicker with out the mods
  • The recess design means you should not need off set cones in the frame to give frame - manifold clearance
  • We offer 3 carb rubbers 1) PHBL 22-25mm has a step inside the manifold 2) PHBH 26-30mm has  astep inside the manifold 3) Mikuni 35mm fits flush to the manifold

 

Reviews

there are no customer reviews at present
want to be the first to offer a review?
to place a review click here

Questions? ( 2 )

Do you have a Question?

If you would like to ask us a question about this product, please feel free to click here to ask a Question Now!



Dave on 24 Jul 2023 asked "Will this also fit an imola 186 cylinder"

MB Scooters Ltd replied: Imolas vary, a photo helps but it should fit

GIANCARLO M on 20 Sep 2019 asked "Is It possibile ti di ti a vforce3 Reed block or does It need machining?"

MB Scooters Ltd replied: Its a straight fit with no modifications



If you feel something is not correct with this product description or image then please contact us using the same link