Lambretta Race-Tour Inlet manifold, TS1, flange type, Dellorto PHBL, MB

MRB0870K

New style inlet manifold from MB Scooters.

Uses a flange type rubber to increase panel clearance and facilitate the use of different types of carburettors.

The manifold has a slight recess on the reed block surface for improved frame clearance.

Kit comprises:-

  • Inlet manifold, MB
  • Flange type rubber to suit Dellorto PHBL carburettors, MB
  • Jubilee clip
  • Inlet gasket, MB
  • All fasteneners

Advantages are;

  • Lifts the carb giving greater panel clearance and aids fitting an air filter
  • Lifting the carb gives great cable clearance for gears/clutch
  • Lifting the carb means better fuel pipe clearance
  • Easier to get to air and idle screws

TOP TIP - Silicone seal the gaskets and rubber and under the allen screw head to prevent air leaks

WARNING - These fit perfect with standard tanks they may not fit with aftermarket tanks

TIP; Always fit a carb dry, if youre jetting in the bike and constantly removing the carb - wipe clean and dry the rubber and the carb. Always use wide jubilee clips! Tighten just so the carb doesnt move side to side by hand to prevent rubbers slitting. Always carry a spare and if you can bond some rubber onto the cowling to support the carb.



Lambretta Race-Tour Inlet manifold, TS1, flange type, Dellorto PHBL, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, Dellorto PHBL, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, Dellorto PHBL, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, Dellorto PHBL, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, Dellorto PHBL, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, Dellorto PHBL, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, Dellorto PHBL, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, Dellorto PHBL, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, Dellorto PHBL, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, Dellorto PHBL, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, Dellorto PHBL, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, Dellorto PHBL, MB
  • Lambretta Race-Tour Inlet manifold, TS1, flange type, Dellorto PHBL, MB

£ 41.96
Price: £ 34.97 Ex Vat



Temporarily out of stock

Notify Me

Related Items (6)

Lambretta Race-Tour Inlet manifold, TS1, flange type, Mikuni 35mm TMX, Amal 28-34mm, MB
MRB0872K

New style inlet manifold from MB Scooters. Uses a MB flange type rubber to increase panel clearance and facilitate the use of different types of... [more]


£ 48.52£ 40.43 (Ex Vat)
Lambretta Race-Tour Inlet manifold, TS1, flange type, Dellorto PHBH, MB
MRB0871K

New style inlet manifold from MB Scooters. Uses a flange type rubber to increase panel clearance and facilitate the use of different types of carburettors. The... [more]


£ 42.59£ 35.49 (Ex Vat)
Lambretta Race-Tour Inlet manifold, TS1, flange type, manifold only, MB
MRB0869K

New style inlet manifold from MB Scooters. Uses a flange type rubber to increase panel clearance and facilitate the use of different types of carburettors. The manifold... [more]


£ 24.50£ 20.42 (Ex Vat)
Lambretta Race-Tour Inlet manifold carb mounting rubber flange type, Mikuni TMX 35mm, Amal 28-35mm, MB
MRB0819

This is a Mark Broadhurst redesigned, improved and strengthened flange type carb mounting rubber.     Suits all Mikuni 32 - 35mm and Amal... [more]


£ 19.14£ 15.95 (Ex Vat)
Lambretta Race-Tour Inlet manifold carb mounting rubber flange type, Dellorto PHBH, Viton, MB
MRB0833

This is a Mark Broadhurst redesigned, improved and strengthened flange type carb mounting rubber.     Suits: Dellorto PHBH carbs 26, 28, 30mm Dellorto VHSH 30mm Dellorto... [more]


£ 16.20£ 13.50 (Ex Vat)
Lambretta Race-Tour Inlet manifold carb mounting rubber flange type, Dellorto PHBL, MB
MRB0817

This is a Mark Broadhurst redesigned, improved and strengthened flange type carb mounting rubber.     Suits all Dellorto 22 - 26mm PHBL and... [more]


£ 15.58£ 12.98 (Ex Vat)


Tips

 

  • The manifold is made with a round hole to suit directly into V Force reed bloocks which give the best power
  • We have reed stuffers for Genuine Yamaha and Bgm reed assemblys so they fit perfect into the round hole
  • If using a square hole reed assembly they can easily be modified to suit but should flow quicker with out the mods
  • The recess design means you should not need off set cones in the frame to give frame - manifold clearance
  • We offer 3 carb rubbers 1) PHBL 22-25mm has a step inside the manifold 2) PHBH 26-30mm has  astep inside the manifold 3) Mikuni 35mm fits flush to the manifold

 

Reviews

there are no customer reviews at present
want to be the first to offer a review?
to place a review click here

Questions? ( 2 )

Do you have a Question?

If you would like to ask us a question about this product, please feel free to click here to ask a Question Now!



David F on 14 May 2023 asked "What would be the best sealent to use and is there a specific torque setting for the Allen bolts on the rubber thanks msrk"

MB Scooters Ltd replied: Use MBU0901

Sharon b on 28 Apr 2020 asked "Do theses tit ok with a sip long range tank ??"

MB Scooters Ltd replied: Ive not seen one so not sure, when I designed the manifold there wasnt all these tanks around so now fit most hit



If you feel something is not correct with this product description or image then please contact us using the same link