Parts index
We stock over 23 Inlet manifold sundries
This section contains various sundry items associated with inlet manifolds. Things like studs, nuts, washers and screws.
MBFCSSS6X20
Amongst many applications this fastener can specifically be used to secure our TS1 inlet where no pack plate is used.... [more]
MBFCSSS6X25
Amongst many applications this fastener can specifically be used to secure our TS1 inlet where a pack plate is used.... [more]
MBFPWA6
This fastener has universal applications.... [more]
MBFPWA7
Amongst many applications this fastener can specifically be used on Lambretta exhaust and inlet manifolds and Vespa engine casings.... [more]
MBFST6X33TS1
This stud can be used to secure the crankcase side but is also as used as an inlet stud on our TS1 manifolds. It is... [more]
MBFST7X34SS
This remade stainless steel stud is designed for use with standard type cylinders where it can be used as the short inlet stud. ... [more]
MBFST7X50SS
This remade stainless steel stud is designed to be used as the long inlet stud on a piston ported type Lambretta cylinder. 7mm x 15... [more]
MBFSW7SS
This fastener has universal applications. Used on Lambretta exhaust and inlet manifolds as well as the screw on the runner arm.... [more]
MBP0162
This Mark Broadhurst redesigned, improved and strengthened Viton carb mounting rubber suits all Mikuni 32-35mm, Dellorto 30 - 32mm VHSA and Amal 28-34mm carbs. ... [more]
MBFH7X42
Specially made MB stainless steel bolt to fit most Lambretta Inlet manifolds. It can often be hard to get to the hexagon head. ... [more]
MRB0825
This is a stub adapter to convert the MB Shorty Reed block to use the new MB flange rubbers offering rubbers to suit many... [more]
MBP0495
This Mark Broadhurst redesigned, improved and strengthened Viton carb mounting rubber which suits all 34/36mm Dellorto VHSB carburettors. Comes marked with MB. Fits carb spigot 44mm... [more]
MBU0089
This Mark Broadhurst redesigned, improved and strengthened Viton carb mounting rubber allows the use of a Dellorto 34/36mm VHSB carburettor on a manifold designed for... [more]
MBL1546
This is the reed valve assembly to suit our MB Race-Tour Reed manifold assembly. Pound for pound this gives a better higher spread... [more]
MRB0874
This is a Mark Broadhurst redesigned, improved and strengthened flange type carb mounting rubber. Suits all Dellorto 34 - 36mm VHSB carbs or any other... [more]
MRB0817
This is a Mark Broadhurst redesigned, improved and strengthened flange type carb mounting rubber. Suits all Dellorto 22 - 26mm PHBL and... [more]
MBP0327
MB designed high quality Viton carb mounting rubber. Simple way to swap carbs if you want to go smaller from say a 34/35mm Mikuni or... [more]
MBGM0074
Bgms Malossi reed rubber to suit MB shorty Reed assembly. This one points down a bit, some head cowlings may need modifying. ... [more]
MBL1552
These are a spare pair of Carbon reeds to suit the Derbi Sender Reed Valve, especially made for MB. These are used on the MB... [more]
MRB0819
This is a Mark Broadhurst redesigned, improved and strengthened flange type carb mounting rubber. Suits all Mikuni 32 - 35mm and Amal... [more]
MRB0873
This Reed stuffer fits the BGM type Yamaha 350 YPVS and Banchee reed blocks. NOTE these are slighty different to genuine Yamaha reed assemblies. Ideally... [more]